RAD Data comm 100 Spezifikationen Seite 278
- Seite / 318
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Chapter 7 Application Tutorial Installation and Operation Manual
7-34 IP DSLAM and WiMAX Backhauling over SDH/SONET Egate-100 Ver. 4.0
³ To configure the logical layer for the E1 port to MiRICi-E1/T1:
• In the Logical Layer menu, configure logical port 47 with GFP protocol
(non-LCAS), with VCAT header disabled, to correspond to physical port 46, as
illustrated in
Figure
7-47
.
Egate-100
Configuration> Logical Layer
1. Port Number[1 - 126] ... (47)
2. Port Name ... (Logical Port 47)
3. Protocol Type > (GFP)
4. Multi Link >...(No)
5. Physical Port Number [1 - 63] > (46)
6. Payload FCS > (Disable)
7. VCAT Header > (Disable)
8. Alarms > (Unmasked)
>
Please select item <1 to 8>
F - Forward Port; B - Backward Port; R - Remove Port
ESC-prev.menu; !-main menu; &-exit
Figure
7-47. Configuring Logical Port for MiRICi-E1/T1
Setting Bridge Parameters
The following steps must be performed:
1. Configuring the bridge to VLAN-aware
2. Configuring the bridge ports as specified in
Table
7-8
3. Defining VLAN memberships as specified in
Table
7-9
.
Configuring the Bridge
The bridge must be configured to VLAN-aware, so that Egate-100 forwards traffic
based on VLAN as well as MAC address.
³ To configure the bridge parameters:
• Navigate to the Bridge menu (Main Menu > Configuration > Applications >
Bridge) and configure the parameter values as illustrated in
Figure
7-20
.
Configuring the Bridge Ports
The bridge ports required for the application are shown in
Table
7-8
. The binding
of bridge port 1 to the host port is automatic in Egate-100, so does not have to
be configured. The bridge ports bound to the host and Fast Ethernet
management port must perform egress tag stripping because they handle
management traffic that had the tag added to the frame, therefore it must be
stripped at egress.
The Port VID can be left as the default value for the bridge ports other than the
Fast Ethernet management port, as user frames arrive tagged. For the Fast
Ethernet port, the Port VID is set to the management VLAN ID.
- Egate-100 1
- Limited Warranty 4
- Product Disposal 4
- General Safety Instructions 5
- Safety Symbols 5
- Handling Energized Products 6
- Attention 8
- FCC-15 User Information 9
- Mise au rebut du produit 10
- Symboles de sécurité 10
- Français 11
- Declaration of Conformity 13
- Glossary 14
- Quick Start Guide 21
- Configuring Basic Parameters 22
- Quick Setup Menu 23
- Contents 27
- Egate-100 Ver. 4.0B iii 29
- Egate-100 Ver. 4.0B v 31
- Chapter 1 33
- Introduction 33
- Features 35
- Classification 37
- Web-based Management 38
- Security 38
- 1.2 Physical Description 39
- 1.3 Functional Description 39
- STM-1 Mapping 41
- SONET Mapping 42
- VLAN-Aware Mode 43
- Ingress Process 44
- Learning Process 45
- Aging Process 45
- Forwarding Process 46
- Egress Process 46
- VLAN-Unaware Mode 47
- Queue Management 50
- Quality of Service 50
- IP Precedence / DSCP 51
- VLAN Priority 51
- Encapsulation 52
- TX Traffic Path 53
- RX Traffic Path 55
- Statistics 56
- Multilink PPP 57
- Management Access 59
- Statistics Collection 61
- Configuration Reset 61
- Chapter 2 67
- Installation and Setup 67
- 2.4 Mounting the Unit 69
- 2.10 Connecting to Power 73
- Chapter 3 75
- Operation 75
- Working with Terminal 79
- Logging In 81
- Principles of Navigation 83
- Hot Keys 83
- Menu Maps 85
- 3.6 Turning Off the Unit 91
- Chapter 4 93
- Configuration 93
- 4-3. Ethernet Traffic Flow 97
- Egate-100 Ver. 4.0 100
- Defining Host Parameters 101
- Configuring SNMPv3 103
- Adding SNMPv3 Users 105
- Assigning Traps 107
- Configuring Target Address 109
- Entering Device Information 111
- Configuring User Access 113
- Configuring Network Managers 115
- 4-22. Radius Parameters 117
- 4-8. Radius Parameters 117
- Configuring the Clock Source 119
- Configuring Protection 121
- FE-UAS – 133
- VCAT support, which is 153
- Configuring the Bridge 155
- Configuring the MAC Table 157
- Configuring the Bridge Ports 157
- Defining Policer Profiles 168
- Defining Shaper Profiles 170
- Defining Queue Profiles 171
- Defining Flows 174
- Viewing SNTP Status 179
- Viewing APS Status 181
- Viewing STM-1/OC-3 Status 184
- Viewing Logical Port Status 189
- Displaying Flow Information 196
- 4-122. View Flow Screen 197
- 4-42. View Flow Parameters 197
- Viewing Inventory 199
- Save your changes 201
- Resetting Egate-100 203
- Chapter 5 205
- Monitoring and 205
- Diagnostics 205
- Viewing Radius Statistics 215
- Alarms and Events 217
- 5-8. System Events List 219
- 5-10. SOH Alarms List 221
- VC Alarms List 221
- Displaying Alarms 229
- Running BERT Test 233
- Viewing Self Test Results 233
- Chapter 6 235
- Software Upgrade 235
- 6.2 Impact 236
- 6.4 Prerequisites 236
- Utilities Menu 237
- Accessing the Boot Menu 240
- 6-10. File Menu 242
- Caution 243
- Chapter 7 245
- Application Tutorial 245
- Mounting the Unit 247
- Connecting to the Terminal 249
- Connecting to AC Power 250
- Connecting to DC Power 251
- Setting SDH/SONET Parameters 253
- Viewing Bridge Statistics 265
- Installing Egate-100 267
- Setting Ethernet Parameters 273
- Running Diagnostic Tests 281
- Equipment List 283
- Setting System Parameters 289
- Configuring T3 and T1 ports 291
- 7-87. Diagnostics Menu 305
- Appendix A 307
- Connection Data 307
- Appendix B 309
- SDH/SONET Mapping 309
- AC/DC Adapter 311
- (AD) Plug 311
- AC/DC Adapter (AD) Plug 312
- Customer Response Form 313
- Error Report 315
- The Access Company 318
Verwandte Produkte und Handbücher für Vernetzung RAD Data comm 100
Vernetzung RAD Data comm ASMi-52L Spezifikationen
(153 Seiten)
(153 Seiten)
Vernetzung RAD Data comm T1 Spezifikationen
(48 Seiten)
(48 Seiten)
Vernetzung RAD Data comm HCD-E1 Spezifikationen
(150 Seiten)
(150 Seiten)
Vernetzung RAD Data comm MiRICi-E3T3 Spezifikationen
(106 Seiten)
(106 Seiten)
Vernetzung RAD Data comm 100 Spezifikationen
(9 Seiten)
(9 Seiten)
Vernetzung RAD Data comm ASM-60 Spezifikationen
(90 Seiten)
(90 Seiten)
Vernetzung RAD Data comm ASMi-52CQ Spezifikationen
(100 Seiten)
(100 Seiten)
Vernetzung RAD Data comm FOM-E3 Bedienerhandbuch
(33 Seiten)
(33 Seiten)
Vernetzung RAD Data comm 146 Bedienungsanleitung
(202 Seiten)
(202 Seiten)
Vernetzung RAD Data comm LA-210 Spezifikationen
(210 Seiten)
(210 Seiten)
Vernetzung RAD Data comm FOMi-T1 Spezifikationen
(58 Seiten)
(58 Seiten)
Vernetzung RAD Data comm T1 Spezifikationen
(158 Seiten)
(158 Seiten)
Vernetzung RAD Data comm HCD-E1 Spezifikationen
(232 Seiten)
(232 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.077 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern