RAD Data comm E1 Interface Converter RIC-E1 Spezifikationen Seite 46
- Seite / 94
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Appendix B IR-ETH Interface Module RIC-E1 Installation and Operation Manual
B-4 Installation and Operation
Figure B-5. IR-ETH DIP Switch and LED Locations
Setting the DIP Switch
Table B-2 describes functions and default settings of the DIP switch SW-1 sections.
The DIP switch is located on the reverse side of the IR-ETH module. To change the
switch settings, you must undo three screws on the board and detach the module
from the main unit.
Table B-2. DIP Switch Settings
Section Name Description Default Setting
1 SQ/FD ON – Full-duplex operation
OFF – Half-duplex operation
OFF
2 CMP ON – Strips padding bits inserted in 64-byte frame
OFF – Transmits frames over WAN as is
OFF
3 FIL ON – Passes only frames destined for another LAN
OFF – Disables LAN filter; passes all frames transparently
OFF
4
– –
Permanently OFF
LED Indicators
Table B-3 and Table B-4 list the IR-ETH LED indicators and describe their functions.
Table B-3. IR-ETH LED Indicators, Standalone RIC-E1
LED Name Description Location Color
LINK ON – Good link integrity Rear panel Green
Note: The LINK indicator is not available for the IR-ETH module with BNC connector.
COLL ON – Collision occurred on the attached Ethernet segment Rear panel Yellow
RX ON – Data is received from the Ethernet attached segment Rear panel Yellow
TX ON – Data is transmitted from RIC-E1 to the attached Ethernet
segment
Rear panel Yellow
ERR D4 ON – Bridge buffer overrun IR-ETH board Red
- E1 Interface Converter 1
- Limited Warranty 4
- General Safety Instructions 5
- Handling Energized Products 6
- FCC-15 User Information 8
- Declaration of Conformity 10
- Quick Start Guide 11
- 2. Operating RIC-E1 12
- Contents 13
- List of Figures 14
- List of Tables 14
- Chapter 1 15
- Introduction 15
- 1.2 Physical Description 16
- 1.3 Functional Description 17
- 1.4 Technical Specifications 18
- Chapter 2 21
- Installation and Setup 21
- 2.3 Configuring RIC-E1 22
- Configuring RIC-E1 2-3 23
- Connecting the Interfaces 24
- Connecting the Power 25
- 2-6 Configuring RIC-E1 26
- Chapter 3 27
- Operation 27
- 3.2 Operating Instructions 28
- Chapter 4 29
- Troubleshooting and 29
- Diagnostics 29
- 4.2 Troubleshooting 30
- Chapter 5 31
- RIC-E1/R Card 31
- 5-2 ASM-MN-214 Card Cage 32
- 5.2 Power Supply 33
- 5.3 RIC-E1/R Front Panel 34
- CHASS-GND 36
- TX&RX CODE 36
- TIMING SEL 36
- Warning 38
- Appendix A 39
- Interface Connector Wiring 39
- [Function] 40
- [Signal 40
- Timing] 40
- A.3 Line Interface Connector 41
- Appendix B 43
- IR-ETH Interface Module 43
- 10BA SE-T 43
- B.2 Technical Specifications 45
- Setting the DIP Switch 46
- LED Indicators 46
- Connecting the LAN 47
- C.1 IR-ETH/QN Options 49
- C.2 Technical Specifications 51
- Setting the DIP Switches 52
- Appendix D 55
- IR-IP Interface Module 55
- D.2 Technical Specifications 56
- D.3 Physical Description 56
- RIC-E1/IP 57
- IR-IP LEDs 58
- IR-IP Controls 58
- Rescue Configuration 61
- Connecting the Telnet Host 62
- What to Do If 64
- D.6 IR-IP Management Utility 65
- D.7 Quick Setup Menu 66
- LAN IP Address 67
- LAN IP Mask 67
- WAN IP Address 67
- WAN IP Mask 67
- Default Gateway 67
- RIC-E1 with IR-IP 68
- DHCP Server 68
- LAN IP Address: 192.168.1.2 68
- Mask: 255.255.255.248 68
- IP Network 68
- D.8 Management Access Menu 69
- D.9 Advanced Setup Menu 70
- Interface Parameters Menu 71
- D-18 Advanced Setup Menu 72
- Protocol Field Compression 73
- Authentication Protocol 73
- Multicast IP Menu 74
- Multicast Forwarding 75
- D.10 Device Control Menu 76
- New Software Download Menu 77
- Viewing Error Log Screen 77
- Erasing Configuration 78
- Resets Menu 78
- D.11 View Menu 79
- ARP Tables 80
- Statistics Screen 81
- Using the Ping Function 83
- D.14 Erasing IR-IP Software 84
- Erasing Application Software 85
- Downloading New Software 85
- E.1 Introduction 87
- EXT INT/LBT 88
- INT/LBT Clock Mode 89
- Customer Response Form 91
- Error Report 92
Verwandte Produkte und Handbücher für Vernetzung RAD Data comm E1 Interface Converter RIC-E1
Vernetzung RAD Data comm 100 Spezifikationen
(318 Seiten)
(318 Seiten)
Vernetzung RAD Data comm ASMi-52L Spezifikationen
(153 Seiten)
(153 Seiten)
Vernetzung RAD Data comm T1 Spezifikationen
(48 Seiten)
(48 Seiten)
Vernetzung RAD Data comm HCD-E1 Spezifikationen
(150 Seiten)
(150 Seiten)
Vernetzung RAD Data comm MiRICi-E3T3 Spezifikationen
(106 Seiten)
(106 Seiten)
Vernetzung RAD Data comm 100 Spezifikationen
(9 Seiten)
(9 Seiten)
Vernetzung RAD Data comm ASM-60 Spezifikationen
(90 Seiten)
(90 Seiten)
Vernetzung RAD Data comm ASMi-52CQ Spezifikationen
(100 Seiten)
(100 Seiten)
Vernetzung RAD Data comm FOM-E3 Bedienerhandbuch
(33 Seiten)
(33 Seiten)
Vernetzung RAD Data comm 146 Bedienungsanleitung
(202 Seiten)
(202 Seiten)
Vernetzung RAD Data comm LA-210 Spezifikationen
(210 Seiten)
(210 Seiten)
AT&T SPIRIT 308 manuali
Manuali dei proprietari e guide per l'utente per Telefoni AT&T SPIRIT 308.
We fornisce 1 manuali pdf AT&T SPIRIT 308 per scaricare gratuitamente in base al tipo di documento: Manuale Utente
Kommentare zu diesen Handbüchern